{"title":"Reloading Organization","description":"\u003cp\u003eStorage that keeps your reloading dies, shell holders and toolheads organized and easy to reach, made in small batches in Georgia, USA, from US-made PCTG.\u003c\/p\u003e\n\u003cp\u003eThe \u003ca href=\"\/products\/reloading-die-holder\"\u003eReloading Die Holder\u003c\/a\u003e holds 8 or 16 standard 7\/8-14 dies in two rows, with a shell holder spot for every four dies so each die set stays with its shell holder. Choose a weighted benchtop stand that stays planted without screws, a lower-priced Bring Your Own Ballast stand you fill yourself, or a wall mount base. Racks swap between bases, and extra bases and rack sets are sold separately in \u003ca href=\"\/products\/reloading-die-holder-parts\"\u003eReloading Die Holder Parts\u003c\/a\u003e.\u003c\/p\u003e\n\u003cp\u003eIt's tested with dies from Lee, RCBS, Hornady and Dillon. Other 7\/8-14 dies with lock rings should fit too, as long as no Hornady Lock-N-Load or Lee Breech Lock bushing is installed.\u003c\/p\u003e\n\u003cp\u003eThe \u003ca href=\"\/products\/benchtop-toolhead-stand-for-dillon-550-toolheads\"\u003eToolhead Stand for Dillon 550\u003c\/a\u003e holds a toolhead with its dies, shellplate and locator pins, and links side by side with more stands into one solid row. Add a stand with each caliber conversion and move the whole row when your bench changes.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eComing soon:\u003c\/strong\u003e a toolhead stand for Dillon 650\/750 presses.\u003c\/p\u003e\n\u003cp\u003e\u003cem\u003eLee, RCBS, Hornady and Dillon are named only to describe compatibility. Purple Primer Store is not affiliated with or endorsed by any of them.\u003c\/em\u003e\u003c\/p\u003e","products":[{"product_id":"benchtop-toolhead-stand-for-dillon-550-toolheads","title":"Toolhead Stand for Dillon 550","description":"\u003ch2\u003eCompact, linkable storage for your Dillon 550 toolheads\u003c\/h2\u003e\n\u003cp\u003eThese stands sit on rubber feet on a shelf or the back of your bench, and they screw together side by side into one solid stand that's easy to rearrange. Each one holds everything for one caliber and adds about 3.25 in to a row, so 11 linked stands fit in about 3 ft.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eHolds:\u003c\/strong\u003e One toolhead with dies installed, plus its shellplate and all three locator pins\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e Dillon RL550 and BL550 toolheads, every 550 shellplate and every locator pin size\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSize:\u003c\/strong\u003e 3.5 in wide, 4.4 in deep and 1.65 in tall; each stand adds about 3.25 in to a row\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLinking:\u003c\/strong\u003e Side by side, all facing the same way, with two M3 screws per joint\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e US-made PCTG, a tough engineering polymer\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColor:\u003c\/strong\u003e Black\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMounting:\u003c\/strong\u003e Freestanding on rubber feet, or screwed down with #6 wood screws\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAssembly:\u003c\/strong\u003e None. To link stands, you'll need a 2.5 mm Allen wrench (not included)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMade in:\u003c\/strong\u003e Georgia, USA\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eShips:\u003c\/strong\u003e Within 3 business days, free on orders of $50 or more\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eA whole caliber in one spot:\u003c\/strong\u003e The toolhead drops in with its dies installed and adjusted, and the powder funnel stays in the powder die. The shellplate stands in a cradle up front. The locator pins sit on their own pegs with just enough clearance that even Dillon's smallest pins pull right out. With the shellplate and pins in plain view, it's easy to tell calibers apart at a glance.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eLinks into one solid stand:\u003c\/strong\u003e Each stand ships with two M3 screws parked in brass inserts on its side. To join two stands, lift the toolhead out of one. Take the two parked screws out of the other stand, then drive them from inside the empty stand, through its wall and back into the inserts they came from. The shellplate and locator pins can stay put. A row can run as long as your shelf, and the stand on the end keeps its screws parked so they never get lost.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eGrows and moves with your setup:\u003c\/strong\u003e Add a stand with each new caliber conversion, pull one when you sell a caliber, and move the whole row when you rearrange or upgrade your bench. Nothing is screwed down unless you want it to be. A linked row moves as one piece, and you can lift up to six loaded stands at once. For longer rows, empty the stands or split the row first. Empty rows of any length lift just fine.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eStable on its own, steadier in a row:\u003c\/strong\u003e The stand isn't weighted, but it stays put empty or loaded, and linked stands are far steadier still. A single stand also holds a toolhead with a powder measure mounted, but it can tip over if you bump the tall hopper. Link it to a neighbor or screw it down through the two mounting tabs. Neighboring stands can both hold toolheads with powder measures.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eRoom for your dies:\u003c\/strong\u003e Any setup that fits your 550 should fit the stand too. There's about 2-1\/4 in from the bottom of the lock rings to the surface the stand sits on, and the open floor gives die bodies room to hang down. Die brand doesn't matter, since the dies only need to fit the toolhead.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eTested with:\u003c\/strong\u003e Dillon's own RL550 toolheads in natural, blue and black. The gold finish should fit too, since it's the same toolhead.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eBuilt to take abuse:\u003c\/strong\u003e PCTG was chosen for its toughness. It's impact resistant and rigid enough to carry a toolhead full of steel dies. It also resists most solvents and chemicals used around firearms. The linking screws thread into brass, not plastic, so you can rearrange as often as you like.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eIn the box:\u003c\/strong\u003e One fully assembled stand. The rubber feet, threaded inserts and two linking screws come installed, so there are no loose parts.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eBuilt to keep running:\u003c\/strong\u003e Need a replacement part? Email us at \u003ca href=\"mailto:mail@purpleprimer.us\"\u003email@purpleprimer.us\u003c\/a\u003e. If you'd rather source your own hardware, here's what we use:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eScrews:\u003c\/strong\u003e M3 x 8 mm socket head cap screws (2)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRubber pads:\u003c\/strong\u003e 3\/8 in diameter x 1\/8 in tall rubber bumpers (4), manufacturer part number BS34BL12X25RP\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eFit Guarantee:\u003c\/strong\u003e The stand is built around Dillon's RL550 toolhead, so Dillon 550 toolheads drop right in. If it doesn't work with your toolhead, contact us. Send it back within 30 days of receiving it and we'll refund you. See our \u003ca href=\"\/policies\/refund-policy\"\u003erefund policy\u003c\/a\u003e for details.\u003c\/p\u003e\n\u003cp\u003e\u003cem\u003eDillon, RL550 and BL550 are named only to describe compatibility. Purple Primer Store is not affiliated with or endorsed by Dillon Precision Products, Inc.\u003c\/em\u003e\u003c\/p\u003e","brand":"Purple Primer","offers":[{"title":"Default Title","offer_id":54382118895899,"sku":"PP-TH-550-BENCH","price":15.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0857\/6863\/4651\/files\/linked-550-stands-front.jpg?v=1792971627"},{"product_id":"reloading-die-holder-parts","title":"Reloading Die Holder Parts","description":"\u003ch2\u003eReplacement bases and rack sets for your Reloading Die Holder\u003c\/h2\u003e\n\u003cp\u003eEvery Reloading Die Holder is a rack set on a base, and any rack set fits any base. Replace a lost or damaged part, switch sizes or move your dies from the bench to the wall without buying a whole new holder. You'll find sizes, die clearance and tested die brands on the \u003ca href=\"https:\/\/purpleprimer.us\/products\/reloading-die-holder\"\u003eReloading Die Holder\u003c\/a\u003e page.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e Every Reloading Die Holder\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e US-made PCTG, a tough engineering polymer\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColor:\u003c\/strong\u003e Black\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTools:\u003c\/strong\u003e 2.5 mm Allen wrench (not included)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMade in:\u003c\/strong\u003e Georgia, USA\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eShips:\u003c\/strong\u003e Within 3 business days, free on orders of $50 or more\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eWhat's in each part:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eBenchtop Stand - Weighted:\u003c\/strong\u003e 2 brackets, 2 feet filled with steel shot and 12 M3 x 8 mm socket head cap screws. The feet come with rubber pads and threaded inserts installed, plus a cap over the ballast cavity for shipping.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBenchtop Stand - Bring Your Own Ballast:\u003c\/strong\u003e The same stand with empty feet, ready for you to fill\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWall Mount Base:\u003c\/strong\u003e 2 wall mount brackets and 4 M3 x 8 mm socket head cap screws. Wall screws and anchors aren't included.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e8 Slot Rack Set:\u003c\/strong\u003e 2 racks, each with 4 die slots and 1 shell holder spot\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e16 Slot Rack Set:\u003c\/strong\u003e 2 racks, each with 8 die slots and 2 shell holder spots\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eGrow, shrink or move your holder:\u003c\/strong\u003e Each rack attaches to its base with two M3 screws, the same way on every base. Swap in a 16 slot rack set when your dies outgrow 8 slots, or go back to 8 to free up bench space. Move your racks to a wall mount base when your bench gets crowded. Rack sets don't come with screws, since they use the ones already on your base.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eBring Your Own Ballast:\u003c\/strong\u003e Already have shotgun shot, bullets or other weight on hand? The Bring Your Own Ballast stand has empty feet and costs less. Each foot holds about 1.7 cubic inches, roughly 4.5 oz of steel shot or 6.5 oz of lead shot. Remove the cap, fill the foot, then screw it to its bracket. The bracket covers the opening but doesn't seal it, so we don't recommend anything fine enough to trickle out, like sand. If you use sand anyway, seal it in with a layer of epoxy before attaching the foot. Lighter fill won't be as stable as a full load of steel or lead shot, but you can always screw the stand to your bench with #6 or #8 screws.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWall mount base:\u003c\/strong\u003e Each bracket hangs from a single screw at the top, and its bottom rests against the wall. Assemble the holder first and hang it as one piece so everything lines up. It takes #6 or #8 screws with any common head, like pan or flat head, in a length that suits what you're mounting to. Several can hang side by side or stacked.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eUse the right anchors:\u003c\/strong\u003e Proper anchors are a must, since they set how much the wall mount can hold. Put one screw in a stud and the other in an anchor, or use two anchors or a backer board. On drywall, use anchors with a heavy load rating, like Twist-N-Lock style anchors, toggle bolts or something equally strong. With anchors like these, the wall mount has easily held a full load of dies for years in our testing. Skip the ribbed plastic expansion anchors from typical assortment kits, since they pull out too easily. Hanging several side by side on drywall? Space them far enough apart for your anchors. A backer board removes that limit.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eNeed something not listed?\u003c\/strong\u003e Email us at \u003ca href=\"mailto:mail@purpleprimer.us\"\u003email@purpleprimer.us\u003c\/a\u003e. We can help with single pieces (one rack, bracket or foot), spare screws, larger quantities and anything else your holder needs.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eBuilt to keep running:\u003c\/strong\u003e If you'd rather source your own hardware, here's what we use:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eScrews:\u003c\/strong\u003e M3 x 8 mm socket head cap screws (12 for a benchtop stand, 4 for the wall mount base)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRubber pads (benchtop stand):\u003c\/strong\u003e 3\/8 in diameter x 1\/8 in tall rubber bumpers (8), manufacturer part number BS34BL12X25RP\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBallast (benchtop stand):\u003c\/strong\u003e Steel or lead shot ballast. Standard shotgun shot also works, but shot sold as ballast is much cheaper. We use \u003ca href=\"https:\/\/www.rotometals.com\/steel-shot\/\" rel=\"noopener\" target=\"_blank\"\u003esteel shot ballast from RotoMetals\u003c\/a\u003e.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eFit Guarantee:\u003c\/strong\u003e Rack sets are built around the standard 7\/8-14 die, so most dies drop right in. If a rack set doesn't work with your dies, contact us. Send it back within 30 days of receiving it and we'll refund you. See our \u003ca href=\"\/policies\/refund-policy\"\u003erefund policy\u003c\/a\u003e for details.\u003c\/p\u003e\n\u003cp\u003e\u003cem\u003eTwist-N-Lock and RotoMetals are named only to describe compatibility or sourcing. Purple Primer Store is not affiliated with or endorsed by either.\u003c\/em\u003e\u003c\/p\u003e","brand":"Purple Primer","offers":[{"title":"Benchtop Stand - Weighted","offer_id":54463741231387,"sku":"PP-DHP-STAND-WEIGHTED","price":25.0,"currency_code":"USD","in_stock":true},{"title":"Benchtop Stand - Bring Your Own Ballast","offer_id":54463741264155,"sku":"PP-DHP-STAND-BYOB","price":18.0,"currency_code":"USD","in_stock":true},{"title":"Wall Mount Base","offer_id":54463741362459,"sku":"PP-DHP-WALLBASE","price":8.0,"currency_code":"USD","in_stock":true},{"title":"8 Slot Rack Set","offer_id":54463741296923,"sku":"PP-DHP-RACKS-8","price":9.0,"currency_code":"USD","in_stock":true},{"title":"16 Slot Rack Set","offer_id":54463741329691,"sku":"PP-DHP-RACKS-16","price":14.5,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0857\/6863\/4651\/files\/16-slot-rack-set.jpg?v=1793387705"},{"product_id":"reloading-die-holder","title":"Reloading Die Holder","description":"\u003ch2\u003eOne versatile reloading die rack system for every setup\u003c\/h2\u003e\n\u003cp\u003eMost die holders are stuck in one spot and one size for good. This one packs 8 or 16 dies close together, keeps every one easy to grab and works wherever you have room: freestanding or screwed to the bench, or on the wall.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eCapacity (16 slot):\u003c\/strong\u003e 16 dies in two rows of 8, plus 4 shell holders\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCapacity (8 slot):\u003c\/strong\u003e 8 dies in two rows of 4, plus 2 shell holders\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e Standard 7\/8-14 dies with lock rings up to 1-3\/8 in across\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBases:\u003c\/strong\u003e Weighted benchtop stand, Bring Your Own Ballast benchtop stand or wall mount base; racks swap between them\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSize (benchtop stand):\u003c\/strong\u003e 16 slot is 10.75 in wide, 8 slot is 7 in wide; both are 5 in deep and 5.5 in tall\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSize (wall mount base):\u003c\/strong\u003e 16 slot is 10.75 in wide, 8 slot is 5.25 in wide; both are 2.75 in deep and 5.75 in tall\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e US-made PCTG, a tough engineering polymer\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColor:\u003c\/strong\u003e Black\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMounting:\u003c\/strong\u003e Benchtop stand is freestanding or screws to the bench; wall mount base hangs from two screws. Both take #6 or #8 screws (not included)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBallast (benchtop stand):\u003c\/strong\u003e Steel shot in the feet, or empty feet on Bring Your Own Ballast versions\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAssembly:\u003c\/strong\u003e About 5 minutes with a 2.5 mm Allen wrench (not included)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMade in:\u003c\/strong\u003e Georgia, USA\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eShips:\u003c\/strong\u003e Within 3 business days, free on orders of $50 or more\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eOne rack system, three bases:\u003c\/strong\u003e Every Die Holder is a rack set on one of three bases: the weighted benchtop stand, the Bring Your Own Ballast stand or the wall mount base. Racks swap between bases, so your holder can grow, shrink or relocate as your bench changes. Step up from 8 to 16 slots with a new rack set, or move your racks from the bench to the wall. Extra bases and rack sets are sold separately in our \u003ca href=\"https:\/\/purpleprimer.us\/products\/reloading-die-holder-parts\"\u003eReloading Die Holder Parts\u003c\/a\u003e listing.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eMade for big die collections:\u003c\/strong\u003e Run a progressive press? Your specialty dies, like decappers and bullet pullers, finally have a home, along with the spares that don't live in a toolhead. Load lots of calibers on a single-stage press? Every die is ready to pull and thread in.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eKeep each caliber together:\u003c\/strong\u003e Each group of four die slots has its own shell holder spot, so a full die set and its shell holder stay together. The spots fit standard shell holders from Hornady, RCBS, Redding, Lee and others.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eRoom for long dies:\u003c\/strong\u003e On the benchtop stand, both rows are angled, so top-row dies have about 7 in of clearance below the lock ring. In the bottom row, the slots over the feet (four on the 16 slot, two on the 8 slot) allow 2-1\/8 in below the lock ring, and the rest allow 3 in. On the wall mount base, every slot allows about 2-5\/8 in below the lock ring. On either base, there's no practical limit above the lock ring.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eTested with dies from:\u003c\/strong\u003e Lee, RCBS, Hornady and Dillon. Other brands should fit too, since 7\/8-14 dies share a standard diameter. Each die needs a lock ring to hang in its slot. Dies with Hornady Lock-N-Load or Lee Breech Lock bushings installed won't fit.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eStable without screws:\u003c\/strong\u003e On the weighted benchtop stand, steel shot in the feet keeps the center of gravity low. The stand stays planted whether it's full, empty or loaded on one side only. The mounting holes are there if you'd rather make it permanent.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eBring Your Own Ballast:\u003c\/strong\u003e Already have shotgun shot, bullets or other weight on hand? The Bring Your Own Ballast versions are the same 8 or 16 slot stand with empty feet, at a lower price. Each foot holds about 1.7 cubic inches, roughly 4.5 oz of steel shot or 6.5 oz of lead shot. The feet ship separately from the brackets with a cap over the cavity. Remove the cap, fill the foot, then screw it to its bracket. The bracket covers the opening but doesn't seal it, so we don't recommend anything fine enough to trickle out, like sand. If you use sand anyway, seal it in with a layer of epoxy before attaching the foot. The stability described above assumes a full load of steel or lead shot. Lighter fill won't be as stable, but the mounting holes are always an option.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWall mount base:\u003c\/strong\u003e No room on your bench or shelves for a stand? The wall mount base puts your dies on the wall, makes better use of vertical space and costs less than the benchtop stands. Each bracket hangs from a single screw at the top, and its bottom rests against the wall. Assemble the holder first and hang it as one piece so everything lines up. It takes #6 or #8 screws with any common head, like pan or flat head, in a length that suits what you're mounting to. It goes on any surface strong enough to hold it with screws or anchors, and several can hang side by side or stacked.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eUse the right anchors:\u003c\/strong\u003e Proper anchors are a must, since they set how much the wall mount can hold. Put one screw in a stud and the other in an anchor, or use two anchors or a backer board. On drywall, use anchors with a heavy load rating, like Twist-N-Lock style anchors, toggle bolts or something equally strong. With anchors like these, the wall mount has easily held a full load of dies for years in our testing. Skip the ribbed plastic expansion anchors from typical assortment kits, since they pull out too easily. Hanging several side by side on drywall? Space them far enough apart for your anchors. A backer board removes that limit.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eBuilt to take abuse:\u003c\/strong\u003e PCTG was chosen for its toughness. It's impact resistant and rigid enough to hold 16 steel dies. It also resists most solvents and chemicals used around firearms.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eIn the box:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e2 racks\u003c\/li\u003e\n\u003cli\u003e2 brackets, benchtop or wall mount depending on your base\u003c\/li\u003e\n\u003cli\u003eBenchtop stands only: 2 feet with rubber pads and threaded inserts installed, each with a cap attached for shipping. Weighted feet come filled with steel shot; Bring Your Own Ballast feet come empty.\u003c\/li\u003e\n\u003cli\u003eM3 x 8 mm socket head cap screws: 12 with a benchtop stand, 4 with the wall mount base\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eBuilt to keep running:\u003c\/strong\u003e Need a replacement part? Racks and bases are sold separately in our \u003ca href=\"https:\/\/purpleprimer.us\/products\/reloading-die-holder-parts\"\u003eReloading Die Holder Parts\u003c\/a\u003e listing, and you can email us at \u003ca href=\"mailto:mail@purpleprimer.us\"\u003email@purpleprimer.us\u003c\/a\u003e for anything else. If you'd rather source your own hardware, here's what we use:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eScrews:\u003c\/strong\u003e M3 x 8 mm socket head cap screws (12 for a benchtop stand, 4 for the wall mount base)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRubber pads (benchtop stand):\u003c\/strong\u003e 3\/8 in diameter x 1\/8 in tall rubber bumpers (8), manufacturer part number BS34BL12X25RP\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBallast (benchtop stand):\u003c\/strong\u003e Steel or lead shot ballast. Standard shotgun shot also works, but shot sold as ballast is much cheaper. We use \u003ca href=\"https:\/\/www.rotometals.com\/steel-shot\/\" rel=\"noopener\" target=\"_blank\"\u003esteel shot ballast from RotoMetals\u003c\/a\u003e.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eFit Guarantee:\u003c\/strong\u003e The Die Holder is built around the standard 7\/8-14 die, so most dies drop right in. If it doesn't work with your dies, contact us. Send it back within 30 days of receiving it and we'll refund you. See our \u003ca href=\"\/policies\/refund-policy\"\u003erefund policy\u003c\/a\u003e for details.\u003c\/p\u003e\n\u003cp\u003e\u003cem\u003eHornady, Lee, RCBS, Redding, Dillon and other brands are named only to describe compatibility or sourcing. Purple Primer Store is not affiliated with or endorsed by any of them.\u003c\/em\u003e\u003c\/p\u003e","brand":"Purple Primer","offers":[{"title":"Benchtop Stand - Weighted \/ 8 Slot Rack Set","offer_id":54464811499803,"sku":"PP-DH-BENCH-8","price":34.0,"currency_code":"USD","in_stock":true},{"title":"Benchtop Stand - Weighted \/ 16 Slot Rack Set","offer_id":54464811532571,"sku":"PP-DH-BENCH-16","price":39.5,"currency_code":"USD","in_stock":true},{"title":"Benchtop Stand - Bring Your Own Ballast \/ 8 Slot Rack Set","offer_id":54464811565339,"sku":"PP-DH-BENCH-8BYOB","price":27.0,"currency_code":"USD","in_stock":true},{"title":"Benchtop Stand - Bring Your Own Ballast \/ 16 Slot Rack Set","offer_id":54464811598107,"sku":"PP-DH-BENCH-16BYOB","price":32.5,"currency_code":"USD","in_stock":true},{"title":"Wall Mount Base \/ 8 Slot Rack Set","offer_id":54473089155355,"sku":"PP-DH-WALL-8","price":17.0,"currency_code":"USD","in_stock":true},{"title":"Wall Mount Base \/ 16 Slot Rack Set","offer_id":54473089188123,"sku":"PP-DH-WALL-16","price":22.5,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0857\/6863\/4651\/files\/PXL_20261021_233910833.jpg?v=1792626761"}],"url":"https:\/\/purpleprimer.us\/collections\/reloading-die-holders.oembed","provider":"Purple Primer Store","version":"1.0","type":"link"}